Categories

Manufacturers

Heatshrink

There are no products in this category
Heatshrink
XLP Thinwall, XLH Thinwall High Shrink, XDW Thinwall Glue Lined, SMDW Medium Wall, Medium Wall Orange, STDW Thick Wal...
More

Subcategories

  • XLP Thinwall

    •XLP tubing is a chemically cross-linked tubing that will withstand -75 °C to 135 °C for normal operating conditions •Highly flexible •Full range 1.5mm to 125mm diameter with 2:1 shrink ratio •Flame retardant •Abrasion and impact resistant

  • XLH Thinwall High Shrink

    •Thinwall High Shrink Ratio Tubing is used in areas where the shrink diameters of the smallest and largest shrink vary significantly •Highly flexible •Nominal shrink ratio 3:1 •Flame retardant •Continuous operating temperature - 75°C to 135°C

  • XDW Thinwall Glue Lined

    •XDW is a Thinwalled Heatshrink Tube with a glue lined inner surface •Highly flexible •Very high shrink ratio 3:1 •Flame retardant •Good mechanical adhesion

  • SMDW Medium Wall

    •Medium Walled Cross-Linked Polyolefin Heatshrink Tube which is used primarily for waterproof jointing and sealing cable terminations •Cost effective and quick waterproof jointing •High shrink ratio •High rigidity and tensile strength once shrunk •Resistant to decay, chemicals and corrosion

  • Medium Wall Orange

    •Orange colour Medium Walled Heatshrink Tube which is used primarily for waterproof jointing and sealing cable terminations •Cost effective and quick waterproof jointing •High shrink ratio •High rigidity and tensile strength once shrunk •Resistant to decay, chemicals and corrosion

  • STDW Thick Wall

    •STDW Heatshrink has a much thicker wall than SMDW, and is used in cable joints, repairs and terminations in critical areas •High shrink ratio of 4:1 •Increased wall thickness allows better insulating and protection •Increased rigidity provides higher abrasion and impact resistance •The adhesive is polyamide and sticks very well to most surfaces

  • KEV Boots and Gloves

    •KEV Heatshrink Gloves (boots) are used to seal and waterproof cable terminations •Hot-melt glue liner melts while the glove shrinks •Quick and simple installation of waterproof termination •High resistance to tearing and high tensile strength •Resistant to decay, chemicals and corrosion

  • SRE End Caps

    •End Caps are used for sealing cable ends during installation or storage •A hot melt glue liner bonds the cap to the cable jacket •Quick reliable seal of cable ends •Watertight and unlimited storage life •Resistant to ultraviolet, aggressive soils, chemicals & corrosion

  • RWSM Wrap Around Zipper Tube

    •RWSM Zipper Tube is folded around the cable, zipped up with a stainless steel channel and then shrunk •Cable repair without cutting the cable •Ideal for in situ field installation •Jointing in tight areas •100% waterproof and low water absorption

  • Victoria Pit Kits

    •SEC Kits are used in Consumers Mains Pits to double insulate mains, and act as a moisture block to the conduit or multi-core cable •In Victoria pit consumers mains conductors are DI •The kits are supplied with: A KEV heatshrink glove & 1.7m XLP •Extra hot melt adhesive, emery cloth ,heatshrink bands for phase •These kits are for 50mm2 connections maximum

  • XLP Kits

    •Assorted colours and lengths of XLP tubing packed in a plastic box. The tube can withstand -75 °C to 135 °C for normal conditions •Highly flexible •Full range 1.5mm to 125mm diameter with 2:1 shrink ratio •Flame retardant •Abrasion and impact resistant